My homemade sybian
Posted Sun Mar 04, 2012 03:45 PM
Posted Sun Mar 04, 2012 04:30 PM
Posted Mon Mar 05, 2012 07:51 PM
Plan on building me a sex machine, babe? lol
Posted Mon Mar 05, 2012 09:48 PM
Maybe. Depends on availability of parts.
Posted Mon Mar 05, 2012 10:10 PM
Holding you to this lol
Posted Mon Mar 05, 2012 10:18 PM
Holding cock or balls? And using your hand or your mouth?
Posted Tue Mar 06, 2012 12:46 AM
For starters I'd suggest cutting some semi circle pieces of 3/4" MDF from the front and rear of the machine as well as two supports closer to the middle.
I'd then use 4 6" long 2"x4"s and connect each of the middle semi-circles to each other (two on the bottom two about 5" apart on the top....more on that later)
I would then use six (three per end) 3" long 2x4's to connect the two end semi-circles to the center structure.
Next I would get some bendable wood and attach it to the mdf braces with an air stapler or air nailer and wood glue.
(There is a company called The Install Bay that sells it, most car audio shops will be able to source it for you)
Back to the middle section with the two braces mounted about 5" apart. That is an approximate size as you would need to fabricate a plate to mount an orbital sander between these braces.
Next you will want to stretch some 1/2" closed cell foam over the curved structure and secure it with contact adhesive. After that has set up you will want to get some 4 way stretch vinyl and attach it to the entire structure, completely covering every part of the top of it and allowing about 3" of overlap into the bottom of the structure which you will want to adhere to the inside as well.
Then you would want to build a bottom board (3/4" MDF should work just fine here) that is 15" long by however wide you made the flat side of the semi-circles (plus 3/4" for the bendable board). After you have stretched the vinyl you will want to screw this bottom board to the 2x4's in the structure above. This will serve two purposes: 1st it will allow you have a nice smooth flat surface on which to set the machine down, 2nd it will help to hold the vinyl in place that you just overlapped into the inside of the frame.
The only thing I haven't quite figured out is how to control the amount of vibrations. I'm assuming you could use some sort of 120 VAC potentiometer or inline voltage regulating device for this. Maybe an old dial from a variable speed jigsaw or router or something...
Posted Tue Mar 06, 2012 03:54 PM
Then I made a piece for accommodate the dildo over the screws. This piece i made it whith a kind of putty or mastic like plasticine that it becomes very hard in short time. This piece must be the same internal sice of the ruber dildo.
All the machine is upholstered like you have seen.
The remote control is made whit a potenciometer or power control. This is a piece easy to find in electronics shops and not too expensive. Its easy to install upon the cord of the motor.
I tried to explain the process, I expect you understand, is hard to me.
If you have more questions, i'll try to answer it.
Posted Thu Mar 08, 2012 07:59 AM
Posted Fri Mar 09, 2012 10:55 AM
My dear friend Ppatrick73: I already seen your machine some time ago.... Actually I feel in your debt. Some time ago I was wondering about if would be possible to make a Sybian at home. I typed in Google "homemade sybian" and saw your post at this forum. I took some ideas from your post and began to work. The result is that you have seen in my post. This is because I posted here my Sybian.
Thanks to you and this forum, I could made my own Sybian, that I wanted for long time. To order a Sybian from USA to Europe would cost about 1.500 Euros (about 1.900 Dollars) that was something impossible to me.
Now I am working whith a new homemade striker fucking machine. Soon I will upload a new post about this.
Regards from Spain
Posted Fri Mar 09, 2012 01:39 PM
Posted Mon Mar 19, 2012 06:55 AM
Posted Tue Mar 20, 2012 03:57 PM
Posted Thu Mar 22, 2012 06:35 AM
Great, your machine is a very clever work!
Posted Thu Mar 22, 2012 06:39 AM
Yes, she "appreciates" my work five times in ten minutes... lol